100x100 Porcelain Tiles for Wholesale and Export 1000x1000 mm showpiece format, factory direct from Ardakan

One square metre per piece — the fewest joints any square format in the range can give, for a floor that reads as one continuous plane.

A design at this scale reads as a slab rather than a tile: veining and stone graphics run at near-natural scale.

The fewest pieces per square metre in the whole catalogue, which offsets the slower handling that comes with large open floors.

Specified where the floor itself is the architectural statement rather than a background to the room.

Showrooms

Retail and product showrooms where the floor itself is part of the presentation.

Hotel and Corporate Lobbies

Large open lobbies where a near-seamless floor plane supports the architecture.

Luxury Residential

Feature floors in high-end residential projects where the design budget allows a slab-scale graphic.

Exhibition and Retail Flagship Floors

Flagship spaces where the floor is expected to photograph and read as a single surface.

• Export catalogue and per-model technical datasheets
• Sample boxes before a bulk order
• Full container and mixed container loading
• Distributor and project pricing on volume
• Private label and OEM production, subject to factory confirmation

• Commercial invoice
• Packing list
• Certificate of origin
• Bill of lading
• Technical datasheet per model

The nominal size is 1000 × 1000 mm, so one piece covers 1.00 m². The rectified work size and the permitted deviation are stated on each model's datasheet, so quote the code when the tolerance matters to the layout.

Suitability belongs to the model, not the size: finish, thickness and abrasion class decide it. Send your room schedule and the desk will confirm which codes in 100 × 100 cm are approved for floor, for wall, or for both.

Porcelain is pressed and fired to a denser body with very low water absorption, which is why it takes heavier traffic and wet areas. In 100 × 100 cm we also produce white body for lighter duty and a lower delivered cost — the datasheet states the body for each code.

Available finishes are listed in the Finishes & Designs section above, in selected models. Ask the desk to confirm which codes carry the finish and colourway you need before the order is placed.

Yes, this size leaves the works rectified; the datasheet states it per model. A ground edge makes a more uniform installation possible, but the achievable joint width also depends on the substrate and the fixing instructions followed on site.

The figure is taken from each model datasheet and is not published as a single number for the whole size, since it varies by body and by model.

MOQ depends on the model, the design, the production plan, the packing and the destination. Send the requirement through the quotation form and the desk replies with the applicable minimum.

The quantity depends on the pieces per carton, the thickness and the model. It is printed on the packing list attached to every quotation.

Yes to all three. The catalogue and datasheets are sent as PDFs, and sample boxes are dispatched on request — the desk states the preparation time and freight arrangement for your destination.

Yes, factory direct. Minimum order quantity is set per model and destination and is stated on the quotation. A proforma invoice is issued once the models, quantity, destination and incoterm are confirmed.

The works at Ardakan, Yazd, ships to thirty-five countries. Routes are road, rail or sea through Bandar Abbas; the desk confirms the available route, documents and delivery terms for a given destination.

It depends on each model reaching its own MOQ, on the container capacity and payload, and on the production schedule. Mixed loading is confirmed before the proforma invoice is issued.

Commercial invoice, packing list, certificate of origin, bill of lading and the technical datasheet. Any additional certificate is confirmed case by case before shipment.

EXW, FOB, CFR and CIF are quoted where the route to the destination supports them. The desk confirms which terms and which route apply to your market.

Private label and OEM production are discussed case by case. Feasibility, minimum quantity, carton artwork, lead time and brand requirements are confirmed with the factory before an order is accepted.

Tighter than any smaller format in the range. The installer should confirm substrate tolerance against the model datasheet before laying; a large, flat substrate is a precondition for this size, not an option.

Yes. At one square metre per piece, this size is heavier and larger to manoeuvre than the rest of the range and is typically laid with suction frames and a two-person crew.

Both are model specific, depending on thickness and body, and are printed on the packing list attached to every quotation.

Only where a specific model's datasheet and the wall's structural capacity support the weight. This size is specified primarily as a floor format.