40x120 Ceramic Wall Tiles for Wholesale and Export 400x1200 mm large-format wall tile, factory direct from Ardakan

A 1200 mm face at 400 mm width weighs roughly two-thirds of a 60x120 piece, so it installs without a second fitter or a suction frame.

Suits full-height wall runs and vertical stack layouts that a square format cannot produce.

On a shower return, a lift lobby or a column, the 400 mm width lands with fewer cuts than a 600 mm tile would.

The only large format we press in a ceramic body — the large-format proportion without the porcelain body, where the surface is a wall and porcelain is not required.

Full-Height Bathroom Walls

Shower walls and full-height bathroom runs, where the long face reduces the number of horizontal joints.

Hotel Corridors and Lift Lobbies

Vertical stack layouts on corridor and lobby walls, where a large-format look is wanted without porcelain handling weight.

Columns and Returns

Narrow wall widths — shower returns, columns, reveals — where the 400 mm width lands with fewer cuts than a square format.

Feature Walls and Retail Fit-Out

Retail and hospitality feature walls where a marble or stone graphic is wanted at a longer face than a square tile gives.

• Export catalogue and per-model datasheets
• Sample boxes before a bulk order
• Full and mixed container loading
• Distributor and project pricing on volume
• Private label and OEM production, subject to factory confirmation

• Commercial invoice
• Packing list
• Certificate of origin
• Bill of lading
• Technical datasheet per model

The nominal size is 400 × 1200 mm, so one piece covers 0.48 m². The rectified work size and the permitted deviation are stated on each model's datasheet, so quote the code when the tolerance matters to the layout.

Suitability belongs to the model, not the size: finish, thickness and abrasion class decide it. Send your room schedule and the desk will confirm which codes in 40 × 120 cm are approved for floor, for wall, or for both.

This size is produced in White body and Red body only — we do not press a porcelain body at 400 × 1200 mm. Ceramic bodies have a higher water absorption than porcelain and are made for interior use; where a specification calls for porcelain, the range starts at 60x60.

Available finishes are listed in the Finishes & Designs section above, in selected models. Ask the desk to confirm which codes carry the finish and colourway you need before the order is placed.

Yes, this size leaves the works rectified; the datasheet states it per model. A ground edge makes a more uniform installation possible, but the achievable joint width also depends on the substrate and the fixing instructions followed on site.

The figure is taken from each model datasheet and is not published as a single number for the whole size, since it varies by body and by model.

MOQ depends on the model, the design, the production plan, the packing and the destination. Send the requirement through the quotation form and the desk replies with the applicable minimum.

The quantity depends on the pieces per carton, the thickness and the model. It is printed on the packing list attached to every quotation.

Yes to all three. The catalogue and datasheets are sent as PDFs, and sample boxes are dispatched on request — the desk states the preparation time and freight arrangement for your destination.

Yes, factory direct. Minimum order quantity is set per model and destination and is stated on the quotation. A proforma invoice is issued once the models, quantity, destination and incoterm are confirmed.

The works at Ardakan, Yazd, ships to thirty-five countries. Routes are road, rail or sea through Bandar Abbas; the desk confirms the available route, documents and delivery terms for a given destination.

It depends on each model reaching its own MOQ, on the container capacity and payload, and on the production schedule. Mixed loading is confirmed before the proforma invoice is issued.

Commercial invoice, packing list, certificate of origin, bill of lading and the technical datasheet. Any additional certificate is confirmed case by case before shipment.

EXW, FOB, CFR and CIF are quoted where the route to the destination supports them. The desk confirms which terms and which route apply to your market.

Private label and OEM production are discussed case by case. Feasibility, minimum quantity, carton artwork, lead time and brand requirements are confirmed with the factory before an order is accepted.

Yes — 40x120 is the centimetre form used in catalogues and 400x1200 mm is the technical form used on datasheets and in quotations.

Ceramic — white body and red body only. This is the only large-format size we press in a ceramic body; a comparable porcelain large format is available at 60x120.

Only where a specific model's datasheet confirms a floor rating. This size is specified primarily as a wall tile.

It is lighter — roughly two-thirds the weight of a 60x120 piece of similar length — so it typically installs without a second fitter or a suction frame, though site conditions still govern the method.