80x80 Porcelain Tiles for Wholesale and Export 800x800 mm large-format square, factory direct from Ardakan

Large-format joint economy on a square module, which suits rooms that are not obviously directional — no layout decision is needed.

An 800 mm edge is materially easier to lay flat than a 1200 mm one: the substrate tolerance is looser and levelling clips do more of the work.

Half the pieces of a 60x60 floor over the same area, so laying labour drops without moving to a two-person handling format.

Reads as large format in a room too small for 60x120 to land without heavy cutting.

Residential Living Areas

Open-plan living rooms and hallways where a square large-format grid reads calmly without a directional layout decision.

Offices and Showrooms

Commercial floors where a large continuous surface is wanted with easier installation than a 1200 mm format.

Hotel Guest Rooms and Mid-Size Lobbies

Guest rooms and lobbies scaled between a boutique and a flagship hotel, where 80x80 fits the room proportion better than 60x120.

Retail Fit-Out

Retail floors needing large-format joint economy without the substrate preparation a 1200 mm edge demands.

• Export catalogue and per-model technical datasheets
• Sample boxes before a bulk order
• Full container and mixed container loading
• Distributor and project pricing on volume
• Private label and OEM production, subject to factory confirmation

• Commercial invoice
• Packing list
• Certificate of origin
• Bill of lading
• Technical datasheet per model

The nominal size is 800 × 800 mm, so one piece covers 0.64 m². The rectified work size and the permitted deviation are stated on each model's datasheet, so quote the code when the tolerance matters to the layout.

Suitability belongs to the model, not the size: finish, thickness and abrasion class decide it. Send your room schedule and the desk will confirm which codes in 80 × 80 cm are approved for floor, for wall, or for both.

Porcelain is pressed and fired to a denser body with very low water absorption, which is why it takes heavier traffic and wet areas. In 80 × 80 cm we also produce white body and red body for lighter duty and a lower delivered cost — the datasheet states the body for each code.

Available finishes are listed in the Finishes & Designs section above, in selected models. Ask the desk to confirm which codes carry the finish and colourway you need before the order is placed.

Yes, this size leaves the works rectified; the datasheet states it per model. A ground edge makes a more uniform installation possible, but the achievable joint width also depends on the substrate and the fixing instructions followed on site.

The figure is taken from each model datasheet and is not published as a single number for the whole size, since it varies by body and by model.

MOQ depends on the model, the design, the production plan, the packing and the destination. Send the requirement through the quotation form and the desk replies with the applicable minimum.

The quantity depends on the pieces per carton, the thickness and the model. It is printed on the packing list attached to every quotation.

Yes to all three. The catalogue and datasheets are sent as PDFs, and sample boxes are dispatched on request — the desk states the preparation time and freight arrangement for your destination.

Yes, factory direct. Minimum order quantity is set per model and destination and is stated on the quotation. A proforma invoice is issued once the models, quantity, destination and incoterm are confirmed.

The works at Ardakan, Yazd, ships to thirty-five countries. Routes are road, rail or sea through Bandar Abbas; the desk confirms the available route, documents and delivery terms for a given destination.

It depends on each model reaching its own MOQ, on the container capacity and payload, and on the production schedule. Mixed loading is confirmed before the proforma invoice is issued.

Commercial invoice, packing list, certificate of origin, bill of lading and the technical datasheet. Any additional certificate is confirmed case by case before shipment.

EXW, FOB, CFR and CIF are quoted where the route to the destination supports them. The desk confirms which terms and which route apply to your market.

Private label and OEM production are discussed case by case. Feasibility, minimum quantity, carton artwork, lead time and brand requirements are confirmed with the factory before an order is accepted.

It depends on the room and the substrate. 80x80 is a square module that is easier to lay flat and needs no directional layout decision; 60x120 gives fewer joints on a rectangular floor and a longer graphic for book-matching. The desk can compare both against your room schedule.

Less than a 1200 mm format, but tighter than 60x60. The fitter should confirm substrate tolerance against the installation guidance on the model datasheet before laying.

Yes, this size leaves the works rectified, with the tolerance stated per model on the datasheet.

Both are model specific and printed on the packing list attached to every quotation, since they vary with thickness and body.